Fuji NXT H08M Pick-and-place Nozzles

The nozzle head of Fuji NXT H08M placement machine is made of Japanese black ceramics and imported diamond materials and rubber. The nozzle has been verified for long-term use. The nozzle head is not easy to whitish, the wear resistance is very good, and the suction process will not generate static electricity and will not stick materials. The vacuum value reaches the original factory level, and the normal service life is more than 24 months. The nozzle body of Fuji NXT H08M placement machine is made of imported high-quality steel, the surface is coated with diamond film to black, and the specific part is implanted with a two-dimensional identification code. The absorption rate during the absorption process is 99.99%. Fuji NXT H08M Nozzle - Every detail is carefully polished from inside to outside.


Fuji NXT H08M Pick-and-place nozzle model:
Fuji NXT H08M SMT Nozzle Core 0.7mm - Part Number: AA8DX00.
Fuji NXT H08M SMT Nozzle Core 1.0mm - Part Number: AA8LT00.
Fuji NXT H08M SMT Nozzle Core 1.3mm - Part Number: AA8DY00.
Fuji NXT H08M SMT Nozzle Core 1.8mm - Part Number: AA8LW00.
Fuji NXT H08M SMT Nozzle Core 2.5mm - Part Number: AA8LX00.
Fuji NXT H08M SMT Nozzle Core 3.7mm - Part Number: AA8LY00.
Fuji NXT H08M SMT Nozzle Core 5.0mm - Part Number: AA8LZ00.
Fuji NXT H08M SMT Nozzle Core 7.0mm - Part Number: AA8MA00.
Fuji NXT H08M SMT Nozzle Core 10.0mm - Part Number: AA8MB00.
Fuji NXT H08M SMT Nozzle Core 15.0mm - Part Number: AA8MC00.
Fuji NXT H08M SMT Nozzle Core 2.5g - Part Number: AA8ME00.
Fuji NXT H08M SMT Nozzle Core 3.7g - Part Number: AA8MF00.
Fuji NXT H08M SMT Nozzle Core 7.0g - Part Number: AA8MH00.
Fuji NXT H08M SMT Nozzle Core 10.0g - Part Number: AA8MK00.
Fuji NXT H08M SMT Nozzle Core 15.0g - Part Number: AA8ML00.

Comments

Post a Comment

Popular posts from this blog

How does the nozzle of Samsung placement machine correspond to the material selection

Image
Regarding how to choose the material of the Samsung SMT nozzle , the most encountered problem is that many technicians and customers do not know the component selection corresponding to the Samsung nozzle. Today I will briefly introduce how the material of the Samsung SMT nozzle corresponds to the material Selection. Take the nozzle of Samsung Chip Mounter CP-45NEO / CP-45FV as an example: Samsung CP-45NEO Nozzle Assembly: CN020,CN030,CN040,CN065,CN110,CN140,CN220,CN400, CN400N ,CN750, CN1100 Samsung CP-45FV Nozzle Assembly: TN020, TN030 , TN040 , TN065 , TN140 , TN220 , TN400 , TN750 , TN1100 Suction hole diameter: 0.18mm, 0.28mm, 0.38mm, 0.65mm, 1.4mm, 2.2mm, 4.0mm, 7.5mm, 11mm. Selection principle of suction nozzle: 1. The diameter of the selected nozzle hole cannot be larger than the minimum size of the component. 2. The diameter of the selected nozzle hole should not be too small than the minimum size of the component, and the general proportion is 1:1.2-1.7, which is ...
Read more

Solution to the dropping of nozzle of JUKI mounter ke-2050

Image
Juki KE-2050 nozzle is not directly connected to the placement machine, there is actually another part connected between them-nozzle holder. We installed the nozzle of the Juki placement machine KE-2050 on the nozzle holder, and then installed the nozzle holder on the placement machine. This will cause a problem that the nozzle is easily separated from the nozzle holder while playing. The reasons for the above problems may be as follows, we analyze them one by one: 1. The Juki KE-2050 nozzle holder with the nozzle is worn out during use and the size becomes smaller, which does not match the nozzle holder. At this time, replace the new nozzle holder. Of course, this is only a temporary solution to the problem, and the situation needs further analysis. 2. It is not the problem of the entire nozzle holder, but the inner gasket is worn or dropped in production, and it is sufficient to replace or reinstall a gasket. 3. The cause of the brake pads, there should be a phenomenon of jitter in...
Read more

Why is the black material commonly used for the nozzle of the placement machine?

Image
The SMT placement equipment has now become the mark of our fully automatic production line, and the SMT placement equipment can accurately and quickly place components all rely on the role of the nozzle. When we use the nozzle of the placement machine, we will definitely find that the nozzles are all black. Why should we use black nozzles? To understand this problem, we must first know what role the nozzle has? The nozzle of the placement machine is not only the key part of the placement machine to pick and place the sucked component, but also the background when the camera of the optical vision system takes a picture. It mainly uses the suction effect of the vacuum to suck the component, and Use blowing to put the components adsorbed on the nozzle to the coordinate position of the circuit board. Almost every nozzle will have a reflective background, which is mainly to have a good background when the image is taken, so that the target information can be accurately highlighted during ...
Read more